DSAI130D 3BSE003127R1 ABB DSAI130D 3BSE003127R1

DSAI130D 3BSE003127R1輸入輸出模塊也稱為控制模塊，在有控制要求時可以輸出信號，或者提供一個開關量信號，使被控設備動作，同時可以接收設備的反饋信號，以向主機報告，是火災報警聯動系統中重要的組成部分，市場上的輸入輸出模塊都可以提供一對無源常開/常閉觸點，DSAI130D 3BSE003127R1用以控制被控設備，部分廠家的模塊可以通過參數設定，設置成有源輸出（如海灣GST-LD-8301),相對應的還有雙輸入輸出模塊、多輸入輸出模塊等等。

DSAI130D 3BSE003127R1火災報警時，報警控制器通過輸出模塊啟動需要聯動的外控設備，如防排煙閥、送風閥、防火卷簾門、風機、警鈴等，并可接受設備的動作回答。 輸出模塊連接在控制器的回路總線上，可以安裝在所控設備的附近，也可安裝在樓層端子模塊箱內。采用電子寫碼，可以現場編碼。DSAI130D 3BSE003127R1輸出模塊的輸出控制邏緝可以根據工程情況編程完成。當控制器接收到探測器的報警信號后，根據預先編入的程序，控制器通過總線將聯動控制信號輸送到輸出模塊，輸出模塊啟動需要聯動的消防設備；設備動作后會接受一個信號回答。

DSAI130D 3BSE003127R1 ABB DSAI130D 3BSE003127R1

DSAI130D 3BSE003127R1 input and output module, also known as the control module, can output signals when there are control requirements, or provide a switch signal, so that the controlled equipment action, and can receive the feedback signal of the equipment to report to the host, is an important part of the fire alarm linkage system. The input and output modules on the market can provide a pair of passive normally open/normally closed contacts. DSAI130D 3BSE003127R1 is used to control the controlled equipment. Some manufacturers' modules can be set by parameters. Set to active output (such as Gulf GST-LD-8301), corresponding to dual input/output module, multiple input/output module, etc.

DSAI130D 3BSE003127R1 fire alarm, alarm controller through the output module to start the need for linkage of external control equipment, such as smoke prevention and exhaust valve, air supply valve, fire shutter door, fan, alarm bell, and can accept the action of the equipment. The output module is connected to the loop bus of the controller and can be installed near the controlled equipment or in the floor terminal module box. Using electronic write code, can be coded on the spot. The output control logic of DSAI130D 3BSE003127R1 output module can be programmed according to the engineering situation. When the controller receives the alarm signal of the detector, according to the pre-programmed program, the controller transmits the linkage control signal through the bus to the output module, and the output module starts the fire equipment that needs linkage; After the device moves, it receives a signal response.