metro node初始化文檔（一）
一、硬件安裝
?
1.1安裝metro node服務器
1.參考《Dell EMC導軌安裝指南》將服務器安裝到機柜中:
a.拆卸滑道，在目標機柜中連續兩個1U位置安裝。
b.將服務器節點從機箱中卸下，安裝在已安裝好的滑道上。
說明:掛載時，請將下方的Dell Service Tag (DST)放在上方。
2.在每個服務器上安裝一個液晶面板。
3.請保存10GbE SFP光模塊，以便后續安裝。
?
1.2安裝電纜管理組件
1.將CMA附件支架連接到每個服務器的服務器滑道上。
2.將CMA托盤連接到每個服務器的服務器滑道上。
3.將預布線線纜管理臂套件安裝在每個服務器節點的服務器滑道組件上。
a.將CMA內卡(1)連接到左側內滑軌。
b.將CMA外卡(2)連接到左側外固定軌。
c.重復執行。
d.用維可牢搭扣將線纜環和紅色業務線纜固定在機架一側。
注意:確保線環在機架上支撐牢固，不拉扯管理臂內的電纜。
1.3連接CMA套件線纜到服務器節點
下面的Port Map Label圖像顯示了以下步驟的端口分配:
1.安裝WAN SFP光模塊到每個節點的2個WAN接口。
a.將1個10GbE SFP光模塊插入端口圖中標識為“WAN1”的端口。
b.將1個10GbE SFP光模塊插入端口圖中標識為“WAN2”的端口。
c.為確認這些鎖緊牢固，輕輕拉動每個SFP I/O模塊。如果SFP松動:
1.打開彈簧鎖。2.將SFP光模塊完全插入。3.關閉彈簧鎖。4.對每個節點重復操作。
注意:對于本地系統配置:a)將WAN SFP安裝在WAN端口，以妥善保管和/或?qū)砜赡苁褂?/span>;b)確保電纜插頭已到位，在不使用時保護SFP。
2.將LCOM DAC (Direct Attach Copper)線纜連接到每個節點的兩個LCOM端口。
a.將標識為LCOM1的黑色線纜插入端口圖中標識為LCOM1的端口。在每個節點上重復。
b.將標識為LCOM2的黑色線纜連接到端口圖中標識為LCOM2的端口。在每個節點上重復。
c.在各節點連接處輕拉線纜，確認線纜安裝牢固。
3.連接MGMT以太網線至每個節點的兩個MGMT接口。
a.將標識為MGMT1的綠色線纜，按照端口圖的指示連接至對應的MGMT1端口。在每個節點上重復。
b.將標記為“MGMT2”的紫色線纜，按照端口圖，連接到對應的“MGMT2”端口。在每個節點上重復。
c.輕拉各節點連接線纜，確認各節點連接線纜卡扣牢固。
4.連接交流電源線至各節點的電源模塊。
a.將黑色電源線連接到PSU1/接口圖上的黑色“AC power”塊上。
b.將灰色電源線連接到端口圖上的PSU2/灰色“AC power”塊。
c.重復執行。
d.檢查電源線走線路徑是否允許服務器節點在滑道上自由移動。
注意:如圖所示，將電源線套入圈內，用魔術貼固定在電源模塊拉手上。請確保皮帶抬起電源線，防止服務器在使用過程中伸展時綁扎。
1.4將電源線連接到備用電源
黑色和灰色電纜分別連接到公用事業電源。
注意:HA維護需要冗余電源連接。確?；疑秃谏碾娫淳€分別連接到不同的電源。
1.將灰色電源線連接到公用事業設備A PDU (Power Distribution Unit)上。
2.將黑色電源線連接到配電盒B上。
?
1.5檢查motro node連線及電源
1.確保每個節點都從兩個電源分區供電。確認各節點電源模塊的電源拉手均為綠色常亮。
注意:如果電源指示燈不亮，請檢查電源線連接。如果不為綠色常亮，請參考《PowerEdge R640安裝和服務手冊(https://topics-cdn.dell.com/pdf/poweredge-r640_Owners-Manual_en-us.pdf)》了解電源指示燈的狀態。
2.打開兩臺服務器，并在左側前面板檢查健康狀態。
a.確認電源開關指示燈為綠色(右前)。
b.確認左側前方?jīng)]有琥珀色的健康狀態指示燈。
3.檢查MGMT1和MGMT2端口的LINK指示燈是否亮綠燈。
4.確認LCOM1和LCOM2端口的LINK指示燈為亮綠色。
1.6建立Local連接
后續連接時，所有線纜需穿過CMA組件走線至機柜側面。使用魔術貼將電纜固定在CMA和機柜側面。
注意:所有節點連接必須通過CMA組件路由，以保證業務運行時的HA。提供足夠的長度以保持手臂運動和電纜健康。
1.將客戶提供的光纖電纜從前端和后端san連接到兩個控制器上的適當metro node端口。
注意:為避免損壞或污染，請勿觸摸光纖電纜的兩端
注意:請使用冗余的光纖物理鏈路將每臺主機連接到metro node的director節點，每個metro node的director節點連接到后端存儲。為防止數據不可用，請確保存儲視圖下的每個主機都有到集群中兩個控制器的路徑，且多路徑配置可以均勻分布到控制器A和控制器B。
注意:與HBA1相比，HBA2上的光纖連接是反向的。
2.將metro node 的CUST接口連接到雙director的客戶IP網絡?
1.7建立Metro連接
注意:本節僅適用于雙集群' metro '系統配置。關于“l(fā)ocal”系統配置，請?zhí)^本節。
后續連接時，所有線纜需穿過CMA組件走線至機柜側面。使用魔術貼將電纜固定在CMA和機柜側面。
注意:所有節點連接必須經過CMA(機械臂)，以便業務運行過程中進行HA維護。
1.連接集群間廣域網IP連接。確保每個節點(director)有兩條獨立的路徑到另一個集群的每個節點(director)。Metro節點只支持光纖IP WAN連接。
二、初始化準備
2.1準備信息
元數據卷準備
1.元卷:從兩個不同的存儲陣列導出4個大小為>= 80GB的存儲卷。
2.日志卷:從兩個不同的存儲陣列導出4個大小為>=5GB & <=20GB的存儲卷(Metro模式)。
?
系統配置的用戶輸入詳細信息
IP地址規劃
?
?
2.2連接節點
從服務筆記本電腦連接到節點有兩種方式:
1. 通過SVC接口連接。
注意:對于Dell發貨的metro node的7.0版本，通過SVC端口連接不工作。
2. 通過iDRAC Direct Micro-USB接口連接。
?
2.2.1通過SVC接口連接
1.如果機柜中有筆記本電腦托架，則適用此步驟。遵循以下步驟:
●在機柜前方，取下U23位置(距機柜地面38.5英寸)的假面板。將筆記本電腦托盤滑出，放置在托盤上。
●若要松開扎帶，請按下紅色業務電纜固定在托盤上的卡扣。
●將業務線纜連接到筆記本電腦的以太網接口。
●另一端連接到節點的SVC接口。
2.在筆記本電腦上打開瀏覽器，登錄http://128.228.221.2。請按照頁面提示操作，然后轉到步驟3。
注意:如果看不到web頁面，請確認筆記本電腦已啟用DHCP。
3.在筆記本電腦上運行“PuTTY.exe”。
說明:本文檔中有幾個任務使用PuTTY工具登錄管理服務器。您可以使用任何類似的Telnet/SSH客戶端。確保對任何客戶機使用SSH協議(版本2)。如果看到PuTTY安全警告，請閱讀它，然后單擊Yes。
4.在“PuTTY Configuration”窗口中，設置如下圖所示。
5.在“Category”中選擇“SSH”，確保“Preferred SSH protocol version”設置為“2”
6.從“類別”列表中選擇“會話”。2 .在“PuTTY Configuration”窗口單擊“Save”，保存會話設置。
7.在“PuTTY Configuration”界面，單擊“Open”，以“Service”用戶名和業務密碼(業務密碼請咨詢系統管理員)登錄節點。
注意:用戶名服務的默認shell提示符是service@localhost:~>。
8.轉到初始化步驟部分。
2.2.2通過iDRAC Direct Micro-USB接口連接
iDRAC直接USB-NIC功能允許直接訪問iDRAC web接口，而不需要使用iDRAC網絡系統管理端口連接。
1..準備一根Micro-USB 2.0線纜，將線纜的一端連接到系統前面板的“iDRAC Direct Micro-USB”接口。將線纜的另一端連接到業務筆記本電腦的USB接口。
2.啟動任何瀏覽器，然后在地址欄中鍵入https://169.254.0.3。
3.跳過證書錯誤，選擇“繼續瀏覽此網站”。
4. 輸入iDRAC憑據。
5.打開虛擬控制臺，然后單擊啟動虛擬控制臺。
6.使用服務憑據登錄并轉到初始化步驟部分。
?
三、初始化步驟
3.1預配置
注意:
1.該階段為各節點設置EC-01端口的IP地址和修改業務用戶的默認密碼。
2.每個節點都必須執行此步驟。
?
使用service用戶登錄Node-1-1-A。
注意:預配置時，所有節點均顯示EULA的內容。為了執行系統配置，用戶必須接受EULA。由于內容較多，所以下面是使用EULA預配置的控制臺輸出的最短版本。
警告:不要在已經配置好的系統上運行vplex_system_config --start或vplex_system_config -s命令，因?yàn)樗鼤?huì)導致節點固件被關閉，并導致完全集群宕機。
?
service@localhost:/opt/dell/vplex/system_config> vplex_system_config --interview
?
Taking backup of existing SCIF has been started...
Taking backup of existing SCIF has been completed.
Congratulations on your new Dell EMC purchase!
Your purchase and use of this Dell EMC product is subject to and governed by the Dell EMC Commercial Terms of Sale, unless you have a separate written agreement with Dell EMC that specifically applies to your order, and the Dell End User License Agreement (EULA), which are each presented below in the following order:
?
* Commercial Terms of Sale
* End User License Agreement (EULA)
?
The Commercial Terms of Sale for the United States are presented below and are also available online at the website below that corresponds to the country in which this product was purchased. By the act of clicking “I accept,” you agree (or re-affirm your agreement to) the foregoing terms and conditions. To the extent that Dell Inc. or any Dell Inc.’s direct or indirect subsidiary (“Dell”) is deemed under applicable law to have accepted an offer by you: (a) Dell hereby objects to and rejects all additional or inconsistent terms that may be contained in any purchase order or other documentation submitted by you in connection with your order; and (b) Dell hereby conditions its acceptance on your assent that the foregoing terms and conditions shall exclusively control.
IF YOU DO NOT AGREE WITH THESE TERMS, DO NOT USE THIS PRODUCT AND CONTACT YOUR DELL REPRESENTATIVE WITHIN FIVE BUSINESS DAYS TO ARRANGE A RETURN.
?
Commercial Terms of Sale
?
These Commercial Terms of Sale (“CTS”) apply to orders for hardware, software, and services by direct commercial and public sector purchasers and to commercial end-users who purchase through a reseller (“Customer”), unless Customer and Suppliers (defined below) have entered into a separate written agreement that applies to Customer’s orders for specific products or services, in which case, the separate written agreement governs Customer’s purchase and use of such specific products or services.
The term “Supplier(s)” means, as applicable:
?
EMC Corporation (“EMC”)
176 South Street
Hopkinton, Massachusetts 01748
?
and
?
Dell Marketing L.P. (“Dell”)
One Dell Way
Round Rock, Texas 78682
Legal Notices:
Dell_Legal_Notices@Dell.com
?
1. Subject Matter and Parts of CTS.
1.1 Scope. This CTS governs Customer’s procurement and Supplier’s provisioning of Products, Services and Third Party Products (if applicable) (collectively “Offerings”), for Customer’s own internal use.
1.2 Products and Services. “Products” are either: (i) Supplier-branded IT hardware products (“Equipment”) or (ii) Supplier-branded generally available software, whether microcode, firmware, operating systems or applications (“Software”). “Services” are:(a) Supplier’s standard service offerings for maintenance and support of Products (“Support Services”) and (b) consulting, deployment, implementation and any other services that are not Support Services (“Professional Services”). “Third Party Products” means hardware, software, products, or services that are not “Dell” or “Dell EMC” branded. Products exclude Services and Third Party Products.
1.3 Framework. This CTS consists of the main body with the terms and conditions applicable to all Offerings that are in scope, as may be supplemented by additional schedules, containing terms applicable to all or only specific Offerings and shall form an integral part of this CTS (“Schedule(s)”). This CTS does not establish a commitment
of Customer to procure, nor an obligation of Supplier or Affiliate to supply, any Offerings unless the parties have agreed on an Order (as defined below).
1.4 Affiliates. Transactions under this CTS may also involve Dell Inc. or Dell Inc.’s direct or indirect subsidiaries (“Affiliates”).
.
.
.
.
13.7 Entire Agreement. You acknowledge that You have read this EULA, that You understand it, that You agree to be bound by its terms, and that this EULA, along with the Order Terms into which this EULA may be incorporated (as applicable), is the complete and exclusive statement of the agreement between You and Licensor regarding
Your use of the Software. All content referenced in this EULA by hyperlink is incorporated into this EULA in its entirety and is available to You in hardcopy form upon Your request. The pre-printed terms of Your purchase order or any other document that is not issued or signed by Licensor or Dell do not apply to Software. You represent that You did not rely on any representations or statements that do not appear in this EULA when accepting this EULA.
?
Rev.09Sept2020
?
Please press enter to accept End User License Agreement to start the system configuration (default: y):<回車>
?
再次輸入命令vplex_system_config –interview開始配置管理IP
service@director-1-1-a:~> vplex_system_config --interview
Taking backup of existing SCIF has been started...
Taking backup of existing SCIF has been completed.
?
Pre-config phase interview process is started...
Creating System Configuration Inventory File at /etc/opt/dell/vplex/scif.yml
?
VPLEX system details
Enter node's EC01 port details:
IP Address : 10.226.81.155
IP Address is validating, please wait...
Node is already configured with same IP address "10.226.81.155"
Netmask : 255.255.248.0
Gateway : 10.226.80.1
MTU (default: 1500): <回車>
Enter the service user password:
Current password :<回車>
New password :Mi@Dim7T
Retype new password :Mi@Dim7T
Password has been changed successfully for the 'service' user
################### To receive the highest level of support, inform Dell EMC support if there is a change in the service password ###################
################### The service user's password must be the same on all nodes in a cluster ###################
Please review the EC01 port details entered.
clusters:
nodes:
8K5ZY23
interfaces:
EC-01
ip:
address: 10.226.81.155
netmask: 255.255.248.0
gateway: 10.226.80.1
mtu: 1500
Please review the above details. Do you want to proceed(y/n)? (default: y):<回車>
IP configuration is successful on this 8K5ZY23
?
?
按照上述步驟，配置其他節點管理IP地址
?
3.2配置會話腳本（階段1）
注意:在所有節點上成功完成預配置階段后，可以從任何節點執行系統配置命令。為了便于后續使用，請確保所有系統配置命令都在同一個節點上執行。以下示例中，所有系統配置命令均使用Node-1-1-B執行。
1.使用service用戶登錄Node-2-1-B。
2.使用vplex_system_config --interview或vplex_system_config -i命令執行前置會話階段。
?
service@localhost:~> vplex_system_config –i
Do you want to re-run the pre-config phase(y/n)?
Press "y" to re-run or press "enter" to proceed with phase-1 interview. (default: n): <回車>
?
Taking backup of existing SCIF has been started...
Taking backup of existing SCIF has been completed.
?
Phase-1 interview process is started...
Using system configuration file at /etc/opt/dell/vplex/scif.yml
?
VPLEX system details
Choose VPlex configuration.
1. Local
2. Metro
Please select configuration (default: local): 2 ?//如果是本地集群選擇1
Enter 'cluster-1' details:
Service user password : Mi@Dim7T
Re-enter service user password : Mi@Dim7T
Enter 'cluster-1' node details:
Enter 'node-1-1-a' details:
IP address : 10.226.81.155
Enter 'node-1-1-b' details:
IP address : 10.226.81.156
//如果是本地集群則沒有下方cluster-2配置
Enter 'cluster-2' details:
Service user password :
Re-enter service user password :
Enter 'cluster-2' node details:
Enter 'node-2-1-a' details:
IP address : 10.226.81.157
Enter 'node-2-1-b' details:
IP address : 10.226.81.158
Enabling passwordless SSH between the nodes...
Creating .ssh/ directory on node(node-1-1-a) with 10.226.81.155
Creating .ssh/ directory on node(node-1-1-b) with 10.226.81.156
Creating .ssh/ directory on node(node-2-1-a) with 10.226.81.157
Creating .ssh/ directory on node(node-2-1-b) with 10.226.81.158
Generating SSH key on node(node-1-1-a), with 10.226.81.155
Generating SSH key on node(node-1-1-b), with 10.226.81.156
Generating SSH key on node(node-2-1-a), with 10.226.81.157
Generating SSH key on node(node-2-1-b), with 10.226.81.158
Exchanging the key with other nodes from node(node-1-1-a), with 10.226.81.155
Exchanging the key with other nodes from node(node-1-1-b), with 10.226.81.156
Exchanging the key with other nodes from node(node-2-1-a), with 10.226.81.157
Exchanging the key with other nodes from node(node-2-1-b), with 10.226.81.158
Enabled passwordless SSH successfully between the nodes.
Enter NTP server 1 address (default: 127.0.0.1): <回車>
Enter NTP server 2 address (default: ): <回車>
?
Connecting to 10.226.81.155 to fetch gateway and netmask details...
gateway and netmask have been fetched successfully for the node 10.226.81.155
?
Connecting to 10.226.81.156 to fetch gateway and netmask details...
gateway and netmask have been fetched successfully for the node 10.226.81.156
?
Connecting to 10.226.81.157 to fetch gateway and netmask details...
gateway and netmask have been fetched successfully for the node 10.226.81.157
?
Connecting to 10.226.81.158 to fetch gateway and netmask details...
gateway and netmask have been fetched successfully for the node 10.226.81.158
?
Dell service tag and WWN Seed has been read sucessfully for the node 10.226.81.155
?
Dell service tag and WWN Seed has been read sucessfully for the node 10.226.81.156
?
GUID has been read successfully for cluster-1
?
Dell service tag and WWN Seed has been read sucessfully for the node 10.226.81.157
?
Dell service tag and WWN Seed has been read sucessfully for the node 10.226.81.158
?
GUID has been read successfully for cluster-2
?
Please review the details entered.
ntp_server_1: 127.0.0.1
ntp_server_2:
snmp:
clusters
name: cluster-1
director_count: 2
instance: 1
id: 1
guid: 43A52L9
ldap:
call_home:
nodes
8K16Z23
name: director-1-1-A
wwn_seed: 2D60002E
interfaces:
EC-01
role: cust
ip:
address: 10.226.81.155
netmask: 255.255.248.0
gateway: 10.226.80.1
mtu: 1500
LC-00
role: com
ip:
address: 128.221.250.35
netmask: 255.255.255.224
gateway:
mtu: 1500
LC-01
role: com
ip:
address: 128.221.251.35
netmask: 255.255.255.224
gateway:
mtu: 1500
MC-00
role: man
ip:
address: 128.221.252.35
netmask: 255.255.255.224
gateway:
mtu: 1500
MC-01
role: man
ip:
address: 128.221.253.35
netmask: 255.255.255.224
gateway:
mtu: 1500
8K14Z23
name: director-1-1-B
wwn_seed: 2D60002F
interfaces:
EC-01
role: cust
ip:
address: 10.226.81.156
netmask: 255.255.248.0
gateway: 10.226.80.1
mtu: 1500
LC-00
role: com
ip:
address: 128.221.250.36
netmask: 255.255.255.224
gateway:
mtu: 1500
LC-01
role: com
ip:
address: 128.221.251.36
netmask: 255.255.255.224
gateway:
mtu: 1500
MC-00
role: man
ip:
address: 128.221.252.36
netmask: 255.255.255.224
gateway:
mtu: 1500
MC-01
role: man
ip:
address: 128.221.253.36
netmask: 255.255.255.224
gateway:
mtu: 1500
//如果是本地集群則沒有下方cluster-2配置輸出
name: cluster-2
director_count: 2
instance: 1
id: 2
guid: 43A22L9
ldap:
call_home:
nodes
8K17Z23
name: director-2-1-A
wwn_seed: 2D600030
interfaces:
EC-01
role: cust
ip:
address: 10.226.81.157
netmask: 255.255.248.0
gateway: 10.226.80.1
mtu: 1500
LC-00
role: com
ip:
ddress: 128.221.250.67
netmask: 255.255.255.224
gateway:
mtu: 1500
LC-01
role: com
ip:
address: 128.221.251.67
netmask: 255.255.255.224
gateway:
mtu: 1500
MC-00
role: man
ip:
address: 128.221.252.67
netmask: 255.255.255.224
gateway:
mtu: 1500
MC-01
role: man
ip:
address: 128.221.253.67
netmask: 255.255.255.224
gateway:
mtu: 1500
8K11Z23
name: director-2-1-B
wwn_seed: 2D600031
interfaces:
EC-01
role: cust
ip:
address: 10.226.81.158
netmask: 255.255.248.0
gateway: 10.226.80.1
mtu: 1500
LC-00
role: com
ip:
address: 128.221.250.68
netmask: 255.255.255.224
gateway:
mtu: 1500
LC-01
role: com
ip:
address: 128.221.251.68
netmask: 255.255.255.224
gateway:
mtu: 1500
MC-00
role: man
ip:
address: 128.221.252.68
netmask: 255.255.255.224
gateway:
mtu: 1500
MC-01
role: man
ip:
address: 128.221.253.68
netmask: 255.255.255.224
gateway:
mtu: 1500
?
Please review the above details.
Do you want to proceed(y/n)? (default: y): <回車>
?
SCIF has been copied to ['10.226.81.156', '10.226.81.155', '10.226.81.158','10.226.81.157'] successfully.
?
Phase-1 interview process is completed.
?
To start the phase-1 configuration, run the command "vplex_system_config -s".
?
service@localhost:~>
?
3.一旦過程順利完成，然后進入下一個任務。
?
3.3應用會話腳本（階段1 ）
注意:請確保后端線纜連接到SAN。如果端口顯示no-link，則在驗證BE端口狀態時腳本失敗。
1. 需要啟動system_config第一階段進程，使用vplex_system_config -s命令。
回顯信息分為以下兩部分:命令的開始部分和結束部分。
?
service@localhost:~> vplex_system_config –s
Starting the system configuration process for phase 1...
[WARNING]: Skipping plugin (/usr/lib/python3.6/site-packages/ansible/plugins/connection/saltstack.py) as it seems to be invalid: The 'cryptography' distribution was not found and is required by ansible
PLAY [localhost]
**************************************************************************************
****************************************************
TASK [Gathering Facts]
**************************************************************************************
**********************************************
ok: [localhost]
PLAY [cluster*]
**************************************************************************************
*****************************************************
TASK [Gathering Facts]
**************************************************************************************
**********************************************
[WARNING]: Platform linux on host 8K14Z23 is using the discovered Python interpreter at /usr/bin/python3.6, but future installation of another Python interpreter could change this. See https://docs.ansible.com/ansible/2.9/reference_appendices/interpreter_discovery.html for more information. ok: [8K14Z23]
[WARNING]: Platform linux on host 8K17Z23 is using the discovered Python interpreter at /usr/bin/python3.6, but future installation of another Python interpreter could change this. See https://docs.ansible.com/ansible/2.9/reference_appendices/interpreter_discovery.html for more information. ok: [8K17Z23]
[WARNING]: Platform linux on host 8K11Z23 is using the discovered Python interpreter at /usr/bin/python3.6, but future installation of another Python interpreter could change this. See https://docs.ansible.com/ansible/2.9/reference_appendices/interpreter_discovery.html for more information. ok: [8K11Z23]
[WARNING]: Platform linux on host 8KJ0Z23 is using the discovered Python interpreter at /usr/bin/python3.6, but future installation of another Python interpreter could change this. See https://docs.ansible.com/ansible/2.9/reference_appendices/interpreter_discovery.html for more information. ok: [8KJ0Z23]
TASK [cfg_prechecks : Execute multi-user.target command]
**************************************************************************************
[WARNING]: Consider using 'become', 'become_method', and 'become_user' rather than running sudo
ok: [8KJ0Z23]
ok: [8K17Z23]
ok: [8K11Z23]
ok: [8K14Z23]
TASK [cfg_prechecks : validating the multi user target status]
**************************************************************************************
skipping: [8K14Z23]
skipping: [8KJ0Z23]
skipping: [8K11Z23]
skipping: [8K17Z23]
TASK [cfg_display_be_ports : Show wwn details]
**************************************************************************************
skipping: [8K14Z23]
ok: [8KJ0Z23] => {
"msg": "WWN details are: {'Cluster 1': ['0xc001445a802e0800',
'0xc001445a802f0800', '0xc001445a80300800', '0xc001445a80310800',
'0xc001445a802e0900', '0xc001445a802f0900', '0xc001445a80300900',
'0xc001445a80310900'], 'Cluster 2': ['0xc001445a80300800', '0xc001445a80310800',
'0xc001445a80300900', '0xc001445a80310900']}"
}
skipping: [8K11Z23]
skipping: [8K17Z23]
RUNNING HANDLER [cfg_private_interfaces : Remove redundant idrac route]
***********************************************************************************
changed: [8KJ0Z23]
changed: [8K14Z23]
changed: [8K11Z23]
changed: [8K17Z23]
PLAY RECAP
**************************************************************************************
**********************************************************
8K11Z23 : ok=98 changed=34 unreachable=0 failed=0 skipped=129 rescued=0 ignored=0
8K14Z23 : ok=105 changed=34 unreachable=0 failed=0 skipped=161 rescued=0 ignored=0
8K17Z23 : ok=98 changed=35 unreachable=0 failed=0 skipped=129 rescued=0 ignored=0
8KJ0Z23 : ok=111 changed=34 unreachable=0 failed=0skipped=116 rescued=0 ignored=0
localhost : ok=1 changed=0 unreachable=0 failed=0 skipped=0 rescued=0 ignored=0
service@localhost:~>
?
3.4配置iDRAC接入
1.需要啟動iDRAC任務，使用vplex_system_config --idrac命令。
回顯信息分為以下兩部分:命令的開始部分和結束部分。
?
service@director-1-1-b:~> vplex_system_config --idrac
?
Starting the system configuration process for idrac tasks...
PLAY [localhost]
**************************************************************************************
**************************************************************************
TASK [Gathering Facts]
**************************************************************************************
********************************************************************
ok: [localhost]
PLAY [all]
**************************************************************************************
********************************************************************************
TASK [Gathering Facts]
**************************************************************************************
********************************************************************
[WARNING]: Platform linux on host 8K12Z23 is using the discovered Python interpreter at /usr/bin/python3.6, but future installation of another Python interpreter could change this. See https://docs.ansible.com/ansible/2.9/reference_appendices/interpreter_discovery.html for more information. ok: [8K12Z23]
[WARNING]: Platform linux on host 8K13Z23 is using the discovered Python interpreter at /usr/bin/python3.6, but future installation of another Python interpreter could change this. See https://docs.ansible.com/ansible/2.9/reference_appendices/interpreter_discovery.html for more information. ok: [8K13Z23]
[WARNING]: Platform linux on host 8K10Z23 is using the discovered Python interpreter at /usr/bin/python3.6, but future installation of another Python interpreter could change this. See https://docs.ansible.com/ansible/2.9/reference_appendices/interpreter_discovery.html for more information. ok: [8K10Z23]
[WARNING]: Platform linux on host 8K15Z23 is using the discovered Python interpreter at /usr/bin/python3.6, but future installation of another Python interpreter could change this. See https://docs.ansible.com/ansible/2.9/reference_appendices/interpreter_discovery.html for more information. ok: [8K15Z23]
TASK [cfg_idrac_pwd : include_tasks]
**************************************************************************************
******************************************************
included: /opt/dell/vplex/system_config/ansible/roles/cfg_idrac_pwd/tasks/configure.yml for 8K12Z23, 8K13Z23, 8K10Z23, 8K15Z23
TASK [cfg_idrac_hostname : Setting hostname in iDRAC]
**************************************************************************************
*************************************
ok: [8K13Z23]
ok: [8K12Z23]
ok: [8K10Z23]
ok: [8K15Z23]
TASK [cfg_idrac_hostname : include_tasks]
**************************************************************************************
*************************************************
skipping: [8K12Z23]
skipping: [8K13Z23]
skipping: [8K10Z23]
skipping: [8K15Z23]
PLAY RECAP
**************************************************************************************
********************************************************************************
8K10Z23 : ok=16 changed=4 unreachable=0 failed=0 skipped=3 rescued=0 ignored=0
8K12Z23 : ok=17 changed=4 unreachable=0 failed=0 skipped=3 rescued=0 ignored=0
8K13Z23 : ok=16 changed=4 unreachable=0 failed=0 skipped=3 rescued=0 ignored=0
8K15Z23 : ok=16 changed=4 unreachable=0 failed=0 skipped=3 rescued=0 ignored=0
localhost : ok=1 changed=0 unreachable=0 failed=0 skipped=0 rescued=0 ignored=0
service@localhost:~>
?
2.前面的命令成功后，轉到下一個任務。
?
3.5后端路徑zone配置
1.使用實例登錄vplexi，輸入vplexi命令，然后輸入以下命令，查看所有的director端口。
service@localhost:/opt/dell/vplex/bin/system_config>vplexcli
Trying ::1...
Connected to localhost.
Escape character is '^]'.
//此處需要輸入service密碼
VPlexcli:/>
VPlexcli:/> ll clusters/cluster-*/directors/director-*/ports/
?
Example:
VPlexcli:/> ll clusters/*/directors/*/ports/
/clusters/cluster-1/directors/director-1-1-A/ports:
Name Address Role Status RxPower[uW] TxPower[uW] Temp[C] Speed Topology
----- ------------------ --------- ------ ----------- ----------- ---------------- --------
IO-00 ????? 0x0000000000000000 ??????? front-end ? down ?????? 0 ???? 0 ???? 0?????? ?- -
IO-01 ????? 0x0000000000000000 ??????? front-end ? down ?????? 0 ???? 0 ???? 0 ???? ?- -
IO-02 ????? 0xc001445a80360800 ??????? back-end ? up ?????????? 0 ???? 0 ???? 0 ???? 16Gbits/s ???????? p2p
IO-03 ????? 0xc001445a80360900 ??????? back-end ? up ?????????? 0 ???? 0 ???? 0?????? 16Gbits/s ???????? p2p
LC-00 ????? 128.221.250.35| ???????????????? local-com ?up ?????????? - ???? - ???? -?????? 10000 ????? ??????? -
LC-01 ????? 128.221.251.35| ???????????????? local-com ?up ?????????? - ???? - ???? -?????? 10000??????? ??????? -
WC-00 ??? 0.0.0.0| ????????????????????????????? wan-com ? down???????? - ???? - ???? -?????? 10000 ????? ??????? -
WC-01 ??? 0.0.0.0| ????????????????????????????? wan-com ? down ?????? - ???? - ???? -?????? 10000 ????? ??????? -
/clusters/cluster-1/directors/director-1-1-B/ports:
Name Address Role Status RxPower[uW] TxPower[uW] Temp[C] Speed Topology
----- ------------------ --------- ------ ----------- ----------- -------
IO-00 ????? 0x0000000000000000 ??????? front-end ? down ?????? 0 ???? 0 ???? 0 ???? -??????????????? ??????? -
IO-01 ????? 0x0000000000000000 ??????? front-end ? down ?????? 0 ???? 0 ???? 0 ???? -??????????????? ??????? -
IO-02 ????? 0xc001445a80370800 ??????? back-end ? up ?????????? 0 ???? 0 ???? 0?????? 16Gbits/s ???????? p2p
IO-03 ????? 0xc001445a80370900 ??????? back-end ? up ?????????? 0 ???? 0 ???? 0?????? 16Gbits/s ???????? p2p
LC-00 ????? 128.221.250.36| ???????????????? local-com ?up ?????????? - ???? - ???? -?????? 10000 ????? ??????? -
LC-01 ????? 128.221.251.36| ???????????????? local-com ?up ?????????? - ???? - ???? -?????? 10000 ????? ??????? -
WC-00 0.0.0.0| wan-com down - - -10000 -
WC-01 0.0.0.0| wan-com down - - -10000 -
//本地集群沒有下方cluster-2信息輸出
/clusters/cluster-2/directors/director-2-1-A/ports:
Name Address Role Status RxPower[uW] TxPower[uW] Temp[C] Speed Topology
----- ------------------ --------- ------ ----------- ----------- -------
IO-00 ????? 0x0000000000000000 ??????? front-end ? down ?????? 0 ???? 0 ???? 0 ???? -??????????????? ??????? -
IO-01 ????? 0x0000000000000000 ??????? front-end ? down ?????? 0 ???? 0 ???? 0 ???? -??????????????? ??????? -
IO-02 ????? 0xc001445a80380800 ??????? back-end ? up ?????????? 0 ???? 0 ???? 0?????? 16Gbits/s ???????? p2p
IO-03 ????? 0xc001445a80380900 ??????? back-end ? up???????????? 0 ???? 0 ???? 0?????? 16Gbits/s ???????? p2p
LC-00 ????? 128.221.250.67| ???????????????? local-com ?up ?????????? - ???? - ???? -?????? 10000 ????? ??????? -
LC-01 ????? 128.221.251.67| ???????????????? local-com ?up ?????????? - ???? - ???? -?????? 10000 ????? ??????? -
WC-00 ??? 0.0.0.0| ????????????????????????????? wan-com ? down ?????? - ???? - ???? -?????? 10000 ????? ??????? -
WC-01 ??? 0.0.0.0| ????????????????????????????? wan-com ? down ?????? - ???? - ???? -?????? 10000 ????? ??????? -
/clusters/cluster-2/directors/director-2-1-B/ports:
Name Address Role Status RxPower[uW] TxPower[uW] Temp[C] Speed Topology
----- ------------------ --------- ------ ----------- ----------- -------
IO-00 ????? 0x0000000000000000 ??????? front-end ? down ?????? 0 ???? 0 ???? 0 ???? -??????????????? ??????? -
IO-01 ????? 0x0000000000000000 ??????? front-end ? down ?????? 0 ???? 0 ???? 0 ???? -??????????????? ??????? -
IO-02 ????? 0xc001445a80390800 ??????? back-end ? up ?????????? 0 ???? 0 ???? 0 ???? 16Gbits/s ???????? p2p
IO-03 ????? 0xc001445a80390900 ??????? back-end ? up ?????????? 0 ???? 0 ???? 0 ???? 16Gbits/s ???????? p2p
LC-00 ????? 128.221.250.68| ???????????????? local-com ?up ?????????? - ???? - ???? -?????? 10000 ????? ??????? -
LC-01 ????? 128.221.251.68| ???????????????? local-com ?up ?????????? - ???? - ???? -?????? 10000 ????? ??????? -
WC-00 ??? 0.0.0.0| ????????????????????????????? wan-com ? down ?????? - ???? - ???? -?????? 10000 ????? ??????? -
WC-01 ??? 0.0.0.0| ????????????????????????????? wan-com ? down ?????? - ???? - ???? -?????? 10000 ????? ??????? -
根據輸出后端口信息，配置FC交換機zone，將后端口與存儲端口相連。
存儲識別metro node后端口wwn，創建主機將所有后端口關聯到一臺主機。例如MetroNode
?
在metro node下查看存儲
VPlexcli:/> ll clusters/*/storage-elements/storage-arrays/
/clusters/cluster-1/storage-elements/storage-arrays:
Name ????? Connectivity Status???? Auto Switch?????? Ports ??????? Logical Unit Count
---------------------------------------------------------------------------------------------------------
---------------------------------------------------------------------------------------------------------
DellEMC-PowerStore-7777 ???????????????????????? ok ?? - ???? 0x58ccf090492006ff, ???????? 24
0x58ccf098492006ff
DellEMC-PowerStore-FNM00185000184 ???? ok ?? - ???? 0x58ccf090492006eb, ??????? 0
0x58ccf098492006eb
EMC-CLARiiON-FNM00185000853 ?????????? ok ?? true ?0x5006016448a00948, ?????? 302
0x5006016c48a00948
EMC-SYMMETRIX-197900205 ???????????????? error? - ?? 0x50000973b0033405, ?????? 528
0x50000973b0033445
/clusters/cluster-2/storage-elements/storage-arrays:
Name ????? Connectivity Status???? Auto Switch?????? Ports ??????? Logical Unit Count
---------------------------------------------------------------------------------------------------------
---------------------------------------------------------------------------------------------------------
DellEMC-PowerStore-FNM00185000184 ???? ok ?? - ???? 0x58ccf090492206eb, ??????? 126
0x58ccf090492306eb
EMC-CLARiiON-APM00193751210 ?????????? ok ?? true ?0x5006016549e034ef, ??????? 302
0x5006016d49e034ef
EMC-SYMMETRIX-197900209 ???????????????? ok ?? - ???? 0x50000973b00344c4, ?????? 526
0x50000973b00344c5
2.請注意后端端口對應的節點wwn號。
●集群1的wwn示例: 0xc001445a80360800, 0xc001445a80360900, 0xc001445a80370800,0xc001445a80370900
●集群2的wwn示例: 0xc001445a80380800, 0xc001445a80380900, 0xc001445a80390800,0xc001445a80390900
?
3.對步驟2中WWN號為“Voyager”的節點完成后端陣列分區。
4. 為確保所有集群/*/director /*/ports/ node的后端接口I0-02和I0-03正常運行，請執行以下命令。具體操作請參見配置后端路徑zoning的步驟1。
5. 確保系統配置第二階段應用完成后，所有節點的前端接口“I0-00”和“I0-01”均可使用(命令為ll cluster /*/directors/*/ports/)。
6. 請根據“卷前提條件”確保存儲卷可用。
7. zoning完成后，進入下一個任務。
?
