DataDomain硬件節點

1.使用串口連接DD，波特率115200

2.登錄CLI界面，使用用戶名sysadmin，密碼為設備SN。

localhost.localdomain login:sysadmin

Password:<system_serial_number>

3.接受終端用戶許可協議

Press any key then hit enter to acknowledge the receipt of EULA information

4.首次啟動運行配置向?qū)?，您可以通過鍵入config setup手動啟動CLI配置向?qū)А?/span>

5.網絡配置

Network Configuration

Configure Network at this time (yes|no) [no]:yes??? //確認配置網絡

?

Use DHCP

Use DHCP for hostname, domainname, default gateway and DNS servers? (At least one interface needs to be configured using DHCP) (yes|no|?)no??? //不使用DHCP

?

Enter the hostname for this system (fully-qualified domain name)[]:dd.joyoutech.com??? //輸入完全限定域名

Domainname

Enter your DNS domainname []:joyoutech.com??? //域名

?

Ethernet port eth0a

Enable Ethernet port ethMa (yes|no|?) [yes]:yes??? //啟用管理端口

Use DHCP on Ethernet port ethMa (yes|no|?) [no]:no??? //不適用DHCP

Enter the IP address for eth0b [0.0.0.0]:192.158.100.116??? //輸入管理IP

Enter the netmask for eth0b [255.255.255.0]:255.255.255.0?? //子網掩碼

?

Default Gateway

Enter the default gateway IP address:192.168.100.254?? //默認網關

?

IPV6 Default Gateway

Enter the ipv6 default gateway IP address:???? //留空，跳過IPv6網關

?

DNS Servers

Enter the DNS Server list (zero, one, two or three IP addresses):192.168.100.1??? //DNS地址

?

6.顯示網絡設置摘要，輸入Save接受設置

7.其他系統參數

# config set mailserver mail.datadomain.com????? //設置郵件服務器

The Mail (SMTP) server is:mail.datadomain.com

?

# config set location "Dallas Regional Data Center Lab,5000 Apple Drive Suite #130, Dallas, Tx" //設置位置

The System Location is:Dallas Regional Data Center Lab,5000 Apple Drive Suite #130, Dallas, Tx

?

# ntp add timeserver 192.168.101.1??? //設置NTP啟用

Remote Time Servers:192.168.10.1

?

# config set timezone US/Central??? //修改時區

The Timezone name is:US/Central

*** You made a change to the timezone setting. To fully effect this change

*** (in currently running processes), you need to reboot the machine.??? //提示需重啟生效

?

# system reboot??? //重啟

The 'system reboot' command reboots the system.File access is interrupted during the reboot.

Are you sure? (yes|no|?) [no]:yes??? //確定

ok, proceeding.

The system is going down for reboot.

?

?

PowerEdge硬件節點

1.配置iDRAC

使用KVM連接VGA接口，開機按F2進入BIOS，在iDRAC Settings>Network>IPv4 Settings頁面下配置IP地址、子網掩碼、默認網關

在iDRAC Settings>User Configuration頁面，啟動root用戶，并修改root密碼，默認密碼為SN。

?

2.配置 Serial over LAN (SOL)（可選）

注意：啟用SOL會禁用串行控制臺。

使用瀏覽器登錄iDRAC管理地址，用戶名root，密碼為設備SN

選擇Configuration > BIOS Settings > Serial Communications頁面，驗證以下值：

Serial Communication: Auto

Serial Port Address: Serial Device1=COM2, Serial Device2=COM1

External Serial Connector: Serial Device 2

Failsafe Baud Rate: 115200

Remote Terminal Type: VT100/VT220

Redirection After Boot: Enabled

點擊Apply保存配置

選擇iDRAC Settings > Connectivity > Serial Over LAN頁面，設置以下值：

Enable Serial Over Lan: Enable

Baud Rate: 115.2 kbps

Channel Privilege Level Limit: Administrator

Redirect Enable: Enable

Escape Key: ^\ (Ctrl + \)

點擊Apply保存配置

選擇iDRAC Settings > Services頁面，設置以下值：

選擇 Enabled for SSH。

驗證“Port Number”是否設置為 22

點擊Apply保存配置

選擇Configuration > BIOS Settings > Serial Communications頁面，單擊 Apply and Reboot。

?

3.串口連接設備

1.使用串口連接DD，波特率115200。

2.連接iDRAC接口，運行ssh <iDRAC-IP-address> -l <iDRAC-username>輸入密碼登錄，運行console com2命令啟動控制臺。

?

4.初始化配置

初始化配置和DataDomain硬件步驟相同。

?

后續步驟

1.添加許可證、配置其他備份網絡、創建文件系統等操作。

2.使用VTL、Ddboost、或文件系統提供給備份軟件。