此功能包括傳感器溫度的監測和

流量計傳感器線圈的電阻。

8.1.6.1傳感器溫度監測

流量計傳感器中線圈的溫度可以通過使用可調節的

最小/最大限值。當超過設定限值時，通過

可編程數字輸出，具體取決于配置。

線圈溫度是環境溫度和流體溫度的一個因素。測量可以，

例如可用于監測由于流體引起的超溫。測量線圈溫度

間接地通過線圈直流電阻（ABB專利GB 2 348 011）。

8.1.6.2傳感器線圈電阻的監測

流量計傳感器中的線圈可以使用可調節的最小/最大限值進行監測

線圈電阻值。當超過設定限值時，通過

可編程數字輸出，具體取決于配置。

1） 目前，該功能僅適用于沒有防爆或有防爆功能的設備

2區/2區。對于1區/1區的設備，該功能正在準備中（該功能已實施

在軟件中，但不能用于分區1/Div.1中的設備）。

2） 指定的標稱直徑范圍僅對ProcessMaster有效。有效的標稱直徑范圍

衛生碩士是DN 10…100（3/8“…4”）。

該設備有一個內部存儲器，電極的測量值沉積在存儲器中

電導率被循環存儲為具有可調節時間的數據記錄

（1分鐘…45000分鐘）。最多存儲12條數據記錄。當?shù)谑龡l記錄

存儲時，最舊的數據記錄會被自動覆蓋。

可以使用外部診斷工具將數據記錄作為趨勢讀取或分析

（掃描主機）。

8.1.8指紋

變送器中集成的“指紋”數據庫允許您比較

使用當前記錄的值進行工廠校準或調試的時間。

8.1.9檢查接地

此功能允許您檢查設備的電氣接地情況。

在檢查過程中，不能進行流量測量。

使用該功能的條件：

?測量管必須完全裝滿。

?流量計傳感器中不得出現流量。

附加安裝條件：

?流量計傳感器不得配備前置放大器

This function includes the monitoring of the sensor temperature and the monitoring of the?

resistance of the flowmeter sensor's coils.?

8.1.6.1 Sensor temperature monitoring?

The temperature of the coils in the flowmeter sensor can be monitored by using adjustable?

minimum/maximum limit values. When a set limit value is exceeded, an alarm is tripped via the?

programmable digital output, depending on the configuration.?

The coil temperature is a factor of the ambient and fluid temperatures. The measurement can,?

e.g., be used to monitor overtemperature due to the fluid. The coil temperature is measured?

indirectly via the coil DC resistance (ABB patent GB 2 348 011).?

8.1.6.2 Monitoring of the sensor coil resistance?

The coils in the flowmeter sensor can be monitored by using adjustable minimum/maximum limit?

values for the coil resistance. When a set limit value is exceeded, an alarm is tripped via the?

programmable digital output, depending on the configuration.?

1) At present, the function is only available for devices without explosion protection or with explosion protection for?

Zone 2 / Div. 2. For devices in Zone 1 / Div. 1 this function is under preparation (the function is already implemented?

in the software, but cannot be used for devices in Zone 1 / Div. 1).?

2) The specified nominal diameter range is valid for ProcessMaster, only. The nominal diameter range valid for?

HygienicMaster is DN 10 … 100 (3/8 “ ... 4 “).

The device has an internal memory where the measured value for the electrode deposits and?

the conductivity are cyclically stored as a data record with an adjustable time?

(1 min ... 45000 min). A maximum of 12 data records is stored. When the thirteenth record is?

stored, the oldest data record is overwritten automatically.?

The data records can be read out or analyzed as a trend using the external diagnostic tool?

(ScanMaster).?

8.1.8 Fingerprint?

The “fingerprint” database integrated in the transmitter allows you to compare the values at the?

time of factory calibration or commissioning with the currently recorded values.?

8.1.9 Checking the grounding?

This function allows you to check the electrical grounding of the device.?

While the check is in progress, no flow measurement can take place.?

Conditions for using the function:?

? The measuring tube must be completely full.?

? No flow must be occur in the flowmeter sensor.?

Additional installation conditions:?

? The flowmeter sensor must not be provided with a preamp