從“文件”菜單下載DriveAP應用程序到RMIO板！開放區塊

應用程序文件（*.ap）。從驅動器菜單執行下載。啟動已使用的

DriveAP的時間級別。

減少運行功能可用于并聯連接的R8逆變器，

2?12×R8i。減少運行功能，可以繼續

如果逆變器模塊出現故障，則在有限電流下運行。如果其中一個

模塊損壞，必須將其從機柜中取出。參數

需要改變以在電流減少的情況下繼續運行。

?必須遵守安全說明。請參閱上的安全說明

適當硬件手冊或安全手冊的首頁。

?從驅動器上斷開電源電壓和所有輔助電壓。

?從機柜中取出損壞的逆變器模塊。參見適當內容

硬件手冊。

?將裝置附帶的空氣擋板固定到頂部模塊導軌上，以

阻擋氣流通過空的模塊空間。

?禁用隔離模塊的充電監控，即設置開關

ASFC-01板的S1?S3連接到DIS（=禁用）。

?打開電源電壓。INT CONFIG故障（09.06故障字3位7

值為1）現在表示連接的逆變器的數量

模塊已更改。

?如果在有限的電流下繼續操作，則現有的

逆變器模塊必須通過參數16.10 INT CONFIG USER進行設置。

?重置故障并啟動驅動器。PPCS鏈接自動重新配置

并且最大電流在

與新逆變器配置和逆變器標稱電流的關系。

注意：如果INT CONFIG故障再次出現，則并聯連接的數量

參數16.10 INT CONFIG USER定義的逆變器不正確?？匆?jiàn)

信號08.22 INT CONFIG WORD（內部配置字）。

Download DriveAP application to RMIO board from File menu ! Open block

application file (*.ap). Perform Download from Drive menu. Start the used

time levels by DriveAP.

Reduced run function is available for parallel connected R8 inverters,

2?12 × R8i. Reduced run function makes it possible to continue the

operation with limited current if an inverter module(s) is out of order. If one of

the modules is broken, it must be removed from the cabinet. Parameter

change is needed to continue the run with reduced current.

? The safety instructions must be followed. See the safety instructions on

the first pages of the appropriate hardware manual or the safety manual.

? Disconnect the supply voltage and all auxiliary voltages from the drive.

? Remove the broken inverter module from the cabinet. See appropriate

hardware manual.?

? Fasten the air baffle provided with the unit to the top module guide to

block airflow through the empty module space.

? Disable the charging monitoring of the isolated module, i.e. set switch

S1?S3 of the ASFC-01 board to DIS (=disabled).

? Switch on the supply voltage. INT CONFIG fault (09.06 Fault Word 3 bit 7

value is 1) now indicates that the number of the connected inverter

modules has changed.

? If the operation is continued with limited current, number of existing

inverter modules must be set by parameter 16.10 INT CONFIG USER.

? Reset the fault and start the drive. PPCS link is reconfigured automatically

and the maximum current is limited (20.04 MAXIMUM CURRENT) in

relation to the new inverter configuration and inverter nominal current.

Note: If INT CONFIG fault reappears, the number of parallel connected

inverters defined by parameter 16.10 INT CONFIG USER is incorrect. See

signal 08.22 INT CONFIG WORD.?