當將CI520/CI522/CI526連接到總線時，通信接口連接到

帶有調制解調器電纜TK515/TK593/TK803的TC512調制解調器。帶有集成調制解調器的單元

直接連接到總線電纜。

當使用單一介質時，總線電纜必須連接到Advant上的線路1連接器

控制器70（PM810）和S800 I/O站（CI810）。

調制解調器下方應留有足夠的空間，以允許一定的最小彎曲半徑

電纜（上圖中的R）。此半徑取決于電纜類型，通常

100毫米用于設備電纜和室內工業環境的電纜。用于地下和

通常需要半徑等于或大于200mm（≈8“）的海底電纜。

如果出現不確定性，應聯系電纜制造商。

請聯系光纜制造商，了解如何在

安裝在電纜上安裝光學連接器是一項精密的工作，應

由專家執行。電纜供應商通?？梢酝扑]此類專家。

光學連接器為STx4型。

當Advant控制器70通信接口被啟動時，其CDP被配置。

由于通信接口不能是總線管理員，因此在

當前為主的總線管理員。當Advant控制器70

啟動并連接到總線，或者當配置為主控的總線管理員

起動。

在啟動時，Advant控制器70前部的所有LED在

硬件初始化。

當R（RUN）指示燈點亮?xí)r，工作站正在運行。

車站地址

在啟動Advant控制器70之前，必須為其分配一個站號。

通過PM810前面的地址開關來選擇電臺編號。車站

數字必須在1到79之間。請參閱Advant Controller 70文檔

以獲取更多信息。

車站地址與公交車沿線車站的順序無關。他們只是

表示用于指代特定站點的物理地址。

Advant控制器站號用作通信的硬件地址

Advant現場總線100上的接口。

When connecting a CI520/CI522/CI526 to the bus the communication interface is connected to

the TC512 modem with modem cable TK515/TK593/TK803. Units with integrated modems are

connected directly to the bus cable.

When single media is used the bus cable must be connected to the Line 1 connector on Advant

Controller 70 (PM810) and S800 I/O Station (CI810).

Sufficient space should remain beneath the modem to permit a certain minimum bending radius

of the cable (R in the figure above). This radius depends on the cable type and is normally

100 mm for apparatus cable and cable for indoor industrial environments. For underground and

submarine cable, a radius equal to or greater than 200 mm (≈ 8”) is normally required.

The manufacturer of the cable should be contacted in the event of uncertainty.

Contact the optical cable manufacturer about info how to handle the optical cable during

installation. The installation of optical connectors on the cable is a precision work which should

be performed by specialists. The cable supplier can usually recommend such experts.

The optical connectors are of the STx4 type.

When an Advant Controller 70 communication interface is started, its CDPs are be configured.

As the communication interface can not be a Bus Administrator, its CDPs are configured on the

Bus Administrator which currently is master. This is performed when the Advant Controller 70

is started and connected to the bus or when a Bus Administrator configured as master has

started.

At start up all LEDs on the Advant Controller 70 front are lit for about a second during the

hardware init.

The station is running when the R (RUN) indicator is lit.

tation Address

Before starting the Advant Controller 70, it must have been assigned a station number.

The station number is selected with the address switches on the PM810 front. The station

number must be in the range of 1 to 79. Please refer to the Advant Controller 70 documentation

for further information.

The station address has no relation to the order of the stations along the bus. They merely

represent physical addresses which are used to refer to specific stations.

The Advant Controller station number acts as the hardware address of the communication

interface on the Advant Fieldbus 100.?