如何重新啟動/開關電源包含 ACQUITY LC 的 Xevo Tof 系統 - WKB24861 目的 重新啟動/開關電源包含 ACQUITY LC 的 Xevo Tof 系統。 環境 Xevo QTof Xevo G2 Xevo G2-S Xevo G2-XS 所有安裝了 ACQUITY LC 的系統 步驟 將泵手動控制開關（即 Xevo 背面的底部中心位置兩個切換開關中的上面一個）翻轉到向下位置。您需要將開關拉出才能對其進行更改。然后，您應該能在 Tune 頁面看到通知，顯示泵手動控制處于激活狀態。 退出 MassLynx 軟件（關閉 Tune 頁面、液相方法編輯器、控制臺，然后關閉 MassLynx）。 運行 stopACQUITYProcesses（C:\Program files (x86)\Waters Instruments\Bin\StopACQUITYProcesses.cmd 或 StopProcesses.exe）。 重新啟動采集計算機。 關閉 LC 模塊電源。重要說明：關閉 LC 模塊時，請確保連接以太網線纜的模塊（通常為樣品管理器）最后關閉。 關閉 LC 模塊大約 30 秒。 重新打開 LC 模塊。重要說明：請確保連接以太網線纜的模塊最先打開。 如果是 Xevo G2，請關閉外部 EPC（所有其它儀器 EPC 將隨電子線路關閉）。 向下翻轉電子線路切換開關（Xevo 背面兩個切換開關中的下面一個）。 等待大約 30 秒。 向上翻轉 Xevo 背面的電子線路切換開關。 如果是 Xevo G2，請打開外部 EPC（所有其它儀器 EPC 將隨電子線路打開）。 重要說明：等待 5 分鐘，讓 EPC 啟動。 打開 MassLynx 軟件。 打開 Tune 頁面。 打開 View > Vacuum（查看 > 真空），然后打開真空選項卡。確認 Tof 的真空讀數為真（非 1e-8）。如果未顯示真實的 Tof 真空讀數，請?jiān)俅沃匦聠?dòng)。 此外，還需要在 Tune 頁面中查找錯誤信息，顯示泵手動控制開關已處于手動控制位置。此錯誤信息表明，質譜儀和采集計算機之間的通訊正確。 顯示良好的真空讀數后，將泵手動控制開關（上面一個開關）翻轉回自動（向上）位置。 確認第 17 步中記錄的泵手動控制開關錯誤信息已從 Tune 頁面消失。 將 MS 切換到 Operate（運行）模式 How to reboot and power-cycle a Xevo Tof system with ACQUITY LC - WKB24861 Last updatedDec 21, 2021 Save as PDF Share Article number: 24861 OBJECTIVE or GOAL Reboot and power-cycle a Xevo Tof system with ACQUITY LC. ENVIRONMENT Xevo QTof Xevo G2 Xevo G2-S Xevo G2-XS All with ACQUITY LC system attached PROCEDURE Flip the pump override switch (this is the top toggle switch of the two switches in the center at the the bottom on the back of the Xevo) to the down position. You need to pull the switch out to change it. You should then see a notification on the Tune Page that the pump override is active. Exit MassLynx (close the Tune Page, the Inlet Editor, the Console, and then MassLynx). Run stopACQUITYProcesses (C:\Program files (x86)\Waters Instruments\Bin\StopACQUITYProcesses.cmd or StopProcesses.exe). Reboot the acquisition computer. Power-down the LC stack. IMPORTANT: When powering-down the LC stack, ensure that the module with the Ethernet cables attached to it (most commonly the sample manager) is turned off last. Leave the LC stack off for approximately 30 seconds. Turn the LC stack back on. IMPORTANT: Ensure that the module with the Ethernet cables attached to it is turned on first. For a Xevo G2, power-off the external EPC (all other instrument EPCs power-off with the electronics). Flip the electronics toggle switch (the bottom switch of the two toggle switches on the back of the Xevo) down. Wait approximately 30 seconds. Flip the electronics toggle switch on the back of the Xevo up. For a Xevo G2, power-on the external EPC (all other instrument EPCs power-on with the electronics). IMPORTANT: Wait five minutes for the EPC to boot up. Open MassLynx. Open the Tune Page. Go to View > Vacuum, and then the vacuum tab. Verify that the vacuum reading for the Tof is real (not 1e-8). If there is no real Tof vacuum reading, start the reboot again. In the Tune Page, also look for an error message stating that the pump override switch is in the override position. This error message indicates that proper communication exists between the mass spectrometer and the acquisition computer. Once you have a good vacuum reading, flip the pump override switch (the top switch) back to the auto (up) position . Verify that the pump override switch error noted in step 17 is now gone from the Tune Page. Put the MS into Operate mode.